2025 Epiroc Production drill rigs Simba 1254

Information

2025 Epiroc Production drill rigs Simba 1254

Precise drill rig

The Simba 1254 is a hydraulic production drill rig made for limited tunnel sizes. The high-penetration rock drills give you the power to increase your production, no matter the rock conditions. Dual stingers with an angle reading system make setup quick and easy while increasing drilling stability and accuracy. Ergonomic control and accessible service points make it easier for operators to reach higher levels of production. When you need a high-precision, hard-working rig for long-hole drilling, you can rely on the Simba 1254.

Photos

Highlights

  • Bensalem, Pennsylvania
  • 2025
  • Epiroc
  • Production drill rigs Simba 1254
  • Deutz
  • Available
  • 2 310 mm
  • with cabin: 2 800 mm | roof up/down: 2 220/ 2 920 mm| tramming: 2 810 mm

Specifications

  • 2025
  • Epiroc
  • Production drill rigs
  • Simba 1254
  • Horizontal
  • Deutz
  • TCD3.6L4
  • 60 kW (2 300 rpm), 358 Nm (1 600 rpm)
  • China IV
  • Power rating at 2 600 rpm: 55 kW (73 hp)
  • Tires: 8.25R15
  • Emergency and parking brakes, SAHR
  • Service brakes: 2 separate circuits, hydraulically applied fully enclosed wet disc brakes
  • 2x70 Ah | Joystick-controlled spotlight right, LED, 1x35 W, 24 V DC
  • Transformer: 4 kVA| Electrical Direct System, EDS 18 | Starting method: star/delta (380-690 V), direct (1 000 V) | Epiroc Rig Control System (RCS 5) | Advanced Boom Control (ABC) Regular | Transformer: 5 kVA | Direct Control System: 2 (DCS 2) | System: 24 V |Frequency: 50 Hz or 60 Hz | Voltage: 380-1 000 V | Total installed power: 70 kW (main motor 55 kW | Main motor: 55 kW
  • Boom: BUT 29 HD | Rig Alignment Laser RAL650 |
  • Sound level: 123 dB(A) re 1 pW |Rod Handling System, RHS 17 (17+1 rods) mechanized drilling up to 32 m
  • Tramming lights: 18x24 W, 24 V | Working lights: LED, 2x50 W, 2 |
  • Front and rear hydraulic jacks
  • Drill rod length: Minimum hole diameter 45 mm | Cable reel, inner/outer diameter: 660/1 195mm
  • 6 802/7 102/7 410 mm | tramming: 11 440 mm (with 4 310 mm drill steel length)
  • with cabin: 2 800 mm | roof up/down: 2 220/ 2 920 mm| tramming: 2 810 mm
  • 2 310 mm
  • 260 mm
  • 5 100/ 2 500 mm
  • Electric water booster pump, Lowara, FLYGT 5SV, capacity max 100 L/min at 10 bar| Min water inlet pressure 2 bar| Filtration: 10 µm| System pressure, max 230 bar|
  • volume 60 L
  • Automatic differential lock on front and rear axles, limited slip | Clearance outside axles:15° clearance outside axles
  • Front axle, Dana 112
  • Rear axle, Dana 112, ±10° oscillatio
  • Total: 13 500| Boom side: 9 000 kg| Engine side: 4 500 kg
  • Lubricated air for the rock drill |Gradeability at max load on | Spirit level for longitudinal and sidewa| Central lubricatio |12 V outlet for communication |Horn, beacon and reverse alarm |Brake lights | Illuminated stairs for platform LED | Hydrostatic transmission| Hydraulic power steering system | FOPS certified protective canopy | Four-wheel drive| Fixed seat for tramming, including safety belt | Engine after-treatment, EGR+DOC+DPF | Full color 4.3-inch LCD display| Limit switch for cable reel with signal lamp and brake connection| Battery charger | Phase sequence and earth fault indicator | Digital voltmeter/amperage meter in electric cabinet | Percussion hour meter on panel of electric cabinet | Thermal overload protection for electric motors | Ni-Cr plated piston rods (limitations exist) | Electrical hydraulic oil filling pump | Mineral hydraulic oil | Oil filter indicator | Water/oil cooler in stainless stee | Hydraulic oil thermostatOil temperature gauge | Low oil level indicator including shut down | Pumps unloaded at start | Hydraulic pump for rotation | Hydraulic pump for percussion, positioning and feed | Central lubrication for drilling and positioning unit | 1 rear and 1 front stinger |Pendulum arm BHP 12 gives 1.5 m feed parallel positioning in the side walls. Adds additional 1.5 m feed parallel positioning upwards/downwards. | Sliding table BHT 15 gives 1.5 m feed parallel positioning | Rotary Actuator BHR 30 for 360° ring drilling | Rock drill lubrication warning kit | External air supply connection for hole blowing kit
  • Electronically driven piston Compressor:Compressor: Atlas Copco LE7, capacity 12 L/s at 5 400 rpm and 7 bar
  • Adapter: Diameter 38 mm - Length: 435 mm
  • Angle reading instrument ARI 6C| Articulated steering: ±41° steering angle